Eltek flatpack2 2000w 48v
Control logic discharge voltage cutout should match the remote target.Do not run low power mode on discharging tab.Step 17 - Navigate to Telemetry, then Live Stats to observe system operation. Maximum charging rate of rectifier is 42A.Charger voltage target needs to be sufficient for all cells to reach bypass threshold.Low power must be enabled on charging tab.230V AC Computer Network Equipment, MCU Eltek Rectifier Module Flat Pack 2. Power Supply 5G Network Equipment Emerson R48 - 3200E For Inverter / Converter. Digital Control 5G Network Equipment 88.9 X 103 X 243 Mm Size HUAWEI R4850N1. Step 16 - Adjust the remote charging target to suit the application. Eltek Flatpack2 5G Network Equipment Power System 48V 8KW 4U CTO20405.XXX. Step 15 - Navigate to the Remote tab on the Control Logic screen. Note: Make sure to "Device Sync" the changes to the CellMons. Step 14 - Adjust the CellMon bypass voltage to suit the application. ELTEK FLATPACK2 2000W 48V RECTIFIER 241115.100 Rev 4.1 New In Box. Step 13 - Navigate to Hardware, then CellMon tab. When the bypass current for all cellmons is above Final the system will complete charging cycle.When the bypass current is above Initial will trigger the system to low power.Low power current should suit the bypass capability of CellMon.Cell Hi Cutout should be above the CellMon bypass voltage threshold as a safe guard target.Step 12 - Adjust the charging control logic to suit the application. Step 11 - Navigate to Control Logic, then Charging tab. Step 10 - Select Canbus protocol to "Eltek FlatPack2 HE2000/48" and Save.
ELTEK FLATPACK2 2000W 48V FREE
Step 9 - Navigate to Hardware and then Integration tab. Cheap Integrated Circuits, Buy Quality Electronic Components & Supplies Directly from China Suppliers:ELTEK FLATPACK2 48/3000 HE high efficiency power rectifier module 241119.105MC Enjoy Free Shipping Worldwide Limited Time Sale Easy Return. NB: Rectifier should have additional enclosure added to meet relevant compliance. Hot glue does not substitute appropriate insulation below this pcb. Step 7 - On bottom pcb cover the resistor and terminal pins with hot glue
ELTEK FLATPACK2 2000W 48V INSTALL
Step 6 - Install 120 canbus terminating resistor Step 5 - Install Anderson DC battery plug Step 3 - Install canbus communication cable with twisted (~10 per 10cm) Step 2 - Initial rear view of Eltek Flatpack2 without connector socket Step 1 - Install communication cable to charger via CAN port on WatchMon.įor newer WatchMon (note 120 Ohm resistor shares CANbus High and CANbus Lowįor older WatchMon with 4 pin CAN see below Here are the steps to configure the Eltek Flatpack2 2000W 48V HE Power Supply/Rectifier to the WatchMon supervisor.ĬAUTION: Example shown is for a demo LiFePO4 cell pack 16S1P, ensure that you adopt suitable values to your application and comply with the battery suppliers recommendation. The HE rectifier is made fully compliant with the standard Eltek Flatpack2 Rectifier which means it can be used in any FP2 system solution, whether it is in new installations, site expansions, or replacement programs.How to control a Eltek Flatpack2 with WatchMonĬAUTION: Not recommended for new projects, provided for legacy project support With more than 4 billion in-field operating hours and a proven cumulative field MTBF of more than 1,9 million hours, Flatpack 2 HE is the only HE (High Efficiency) rectifier with a proven track record. Since setting the new standard for rectifier efficiency, the Flatpack2 HE family is now available in a variety of voltages and power ratings, all with superior efficiency up to 96.5%.
ELTEK FLATPACK2 2000W 48V SERIES
ABB/GE Industrial Power LP11 924 Series UPS.Eaton Visual Capacity Optimization Manager (VCOM).ASCO PowerQuest CPMS Maintenance Services.Battery Replacement, Testing, and Maintenance.